That means: After the network connection was interrupted, the client should act as if the VPN connection was terminated. However, once the physical network connection gets lost, usually the VPN tunnel is dropped as well (which makes some sense). You can reproduce a similar behavior by simply pulling the Ethernet plug out of the network card if you're on a wired network. This is, by the way, not limited to the standby mode.
Shrew Soft VPN Client, unfortunately, does not detect this connection loss and seems to think that the network connection was not interrupted. This seems to be due to the fact that on notebooks, the physical network connection is dropped in order to save energy when they enter the Standby mode. I experienced similar problems with previous versions of Shrew Soft VPN client as well. Are they aware of this behavior? I hope they I hope, however, Shrewsoft sometime fixes VPN Client so that the VPNĭoes not "hang" like this. That did the trick! Thanks! Now I can fix things without rebooting. Restarting the Shrew services clears this up.
Shrew soft vpn cisco modem Pc#
Once in a blue moon, my PC will get into the state where the Shrew VPN will connect and pass traffic, but the VPN disconnects a short time after (~ 30 seconds).
Shrew soft vpn cisco modem windows#
My experience has been that the "ShrewSoft IKE Daemon" will take a long time to stop, and Windows will complain that it couldn't stop the service, yet it does still stop. Please advise on how this can be resolved.Ģ) Open Control Panel -> System and Security -> Administrative Tools -> Services (right-click the bottom-left Start Screen icon to get to Control Panel in the first place)ģ) Stop both the "ShrewSoft IKE Daemon" and "ShrewSoft IPSEC Daemon" servicesĤ) Verify both services have stopped (F5 to refresh view) The same problem was occurring with v2.2.1 (which I had initially tried "ipconfig" command output does not show anyĭifference between when (VPN is connected and) VPN is working and Identifier, Key ID string, (Remote ID: ID Type: Any) and Options: [NAT Traversal: enable, Port 4500, Keep-alive: 15 sec, IKEįragm.: enable, Max packet size: 540 Bytes, Enable Dead Peerĭetection, Enable ISAKMP Failure Notifications, Enable Client LoginĪuthentication method is "Mutual PSK + XAuth", with ID Type: Key VPN appears to be up (by the way, I wouldĮxpect Shrewsoft VPN Client to understand the outage and drop theĬonnection automatically) If I attempt to manually Disconnect anĬonnect again, I find myself in the above situation (VPN ClientĪdapter mode is "Virtual adapter and assigned address" (AutoĪddress/Netmask), MTU 1380, Auto Config: ike config pull, The same happens if Ethernet connection (physically) drops temporarily Manually, it will need a reboot for the VPN Client to work correctly. Works fine to establish a new connection. If I manually disconnect before Standby, then, after Standby VPN Client Laptop is put to Standby mode by closing the lid, while VPN is active. This is a consistent, reproducible problem.
Re-enabling the Ethernet connection, but nothing works. Have tried restarting the Shrewsoft VPN Client, disabling and More) cannot be resolved in any way, except by rebooting the machine.
Shresoft VPN Client effectively not working any Public IP addresses does not work either - so it's not a DNS problem. Possible, nor VPN access to our Org internal network. Private network I am on a DSL line.) Neither usual Internet access is Issues), no Internet access is available (except local, on my home not using an explicit -manual-ĭiscconnect), then, the next time VPN is -explicitly, pressing theĬonnect button- established (VPN seems to be established without The problem: If an established VPN Connection (over Ethernet, using UTPĬabling) is interrupted abnormally (i.e. I am running Shrewsoft VPN Client v2.2.2 (Free Version). It connects to a Cisco 3825 router running IOS v12.4(9)T2.
Shrew soft vpn cisco modem pro#
Recently, I have started using a Dell laptop running Win 8 Pro 64 bit. First of all, thanks for your great piece of software, which I have been